[PATCH 8/8] Revert "iwlwifi: mvm: treat EAPOLs like mgmt frames wrt rate"

[Emmanuel Grumbach]

From: Emmanuel Grumbach <emmanuel.grumbach-***@public.gmane.org>

This reverts commit aa11bbf3df026d6b1c6b528bef634fd9de7c2619.
This commit was causing connection issues and is not needed
if IWL_MVM_RS_RSSI_BASED_INIT_RATE is set to false by default.

Regardless of the issues mentioned above, this patch added the
following WARNING:

WARNING: CPU: 0 PID: 3946 at drivers/net/wireless/iwlwifi/mvm/tx.c:190 iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]()
Got an HT rate for a non data frame 0x8
CPU: 0 PID: 3946 Comm: wpa_supplicant Tainted: G O 3.17.0+ #6
Hardware name: LENOVO 20ANCTO1WW/20ANCTO1WW, BIOS GLET71WW (2.25 ) 07/02/2014
0000000000000009 ffffffff814fa911 ffff8804288db8f8 ffffffff81064f52
0000000000001808 ffff8804288db948 ffff88040add8660 ffff8804291b5600
0000000000000000 ffffffff81064fb7 ffffffffa07b73d0 0000000000000020
Call Trace:
[<ffffffff814fa911>] ? dump_stack+0x41/0x51
[<ffffffff81064f52>] ? warn_slowpath_common+0x72/0x90
[<ffffffff81064fb7>] ? warn_slowpath_fmt+0x47/0x50
[<ffffffffa07a39ea>] ? iwl_mvm_set_tx_params+0x60a/0x6f0 [iwlmvm]
[<ffffffffa07a3cf8>] ? iwl_mvm_tx_skb+0x48/0x3c0 [iwlmvm]
[<ffffffffa079cb9b>] ? iwl_mvm_mac_tx+0x7b/0x180 [iwlmvm]
[<ffffffffa0746ce9>] ? __ieee80211_tx+0x2b9/0x3c0 [mac80211]
[<ffffffffa07492f3>] ? ieee80211_tx+0xb3/0x100 [mac80211]
[<ffffffffa0749c49>] ? ieee80211_subif_start_xmit+0x459/0xca0 [mac80211]
[<ffffffff814116e7>] ? dev_hard_start_xmit+0x337/0x5f0
[<ffffffff81430d46>] ? sch_direct_xmit+0x96/0x1f0
[<ffffffff81411ba3>] ? __dev_queue_xmit+0x203/0x4f0
[<ffffffff8142f670>] ? ether_setup+0x70/0x70
[<ffffffff814e96a1>] ? packet_sendmsg+0xf81/0x1110
[<ffffffff8140625c>] ? skb_free_datagram+0xc/0x40
[<ffffffff813f7538>] ? sock_sendmsg+0x88/0xc0
[<ffffffff813f7274>] ? move_addr_to_kernel.part.20+0x14/0x60
[<ffffffff811c47c2>] ? __inode_wait_for_writeback+0x62/0xb0
[<ffffffff813f7a91>] ? SYSC_sendto+0xf1/0x180
[<ffffffff813f88f9>] ? __sys_recvmsg+0x39/0x70
[<ffffffff8150066d>] ? system_call_fastpath+0x1a/0x1f
---[ end trace cc19a150d311fc63 ]---

which was reported here: https://bugzilla.kernel.org/show_bug.cgi?id=85691

CC: <stable-***@public.gmane.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach-***@public.gmane.org>
---
drivers/net/wireless/iwlwifi/mvm/tx.c | 8 ++------
1 file changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/mvm/tx.c b/drivers/net/wireless/iwlwifi/mvm/tx.c
index 1cb793a..c6a517c 100644
--- a/drivers/net/wireless/iwlwifi/mvm/tx.c
+++ b/drivers/net/wireless/iwlwifi/mvm/tx.c
@@ -175,14 +175,10 @@ static void iwl_mvm_set_tx_cmd_rate(struct iwl_mvm *mvm,

/*
* for data packets, rate info comes from the table inside the fw. This
- * table is controlled by LINK_QUALITY commands. Exclude ctrl port
- * frames like EAPOLs which should be treated as mgmt frames. This
- * avoids them being sent initially in high rates which increases the
- * chances for completion of the 4-Way handshake.
+ * table is controlled by LINK_QUALITY commands
*/

- if (ieee80211_is_data(fc) && sta &&
- !(info->control.flags & IEEE80211_TX_CTRL_PORT_CTRL_PROTO)) {
+ if (ieee80211_is_data(fc) && sta) {
tx_cmd->initial_rate_index = 0;
tx_cmd->tx_flags |= cpu_to_le32(TX_CMD_FLG_STA_RATE);
return;

[Emmanuel Grumbach]

From: Emmanuel Grumbach <emmanuel.grumbach-***@public.gmane.org>

Cc: <stable-***@public.gmane.org> [3.16+]
Fixes: 2adc8949efab ("iwlwifi: mvm: BT Coex - fix boost register / LUT values")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach-***@public.gmane.org>
---
drivers/net/wireless/iwlwifi/mvm/coex.c | 4 ++--
drivers/net/wireless/iwlwifi/mvm/coex_legacy.c | 4 ++--
2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/mvm/coex.c b/drivers/net/wireless/iwlwifi/mvm/coex.c
index 8df2021..da2ffb7 100644
--- a/drivers/net/wireless/iwlwifi/mvm/coex.c
+++ b/drivers/net/wireless/iwlwifi/mvm/coex.c
@@ -303,8 +303,8 @@ static const __le64 iwl_ci_mask[][3] = {
};

static const __le32 iwl_bt_mprio_lut[BT_COEX_MULTI_PRIO_LUT_SIZE] = {
- cpu_to_le32(0x28412201),
- cpu_to_le32(0x11118451),
+ cpu_to_le32(0x2e402280),
+ cpu_to_le32(0x7711a751),
};

struct corunning_block_luts {
diff --git a/drivers/net/wireless/iwlwifi/mvm/coex_legacy.c b/drivers/net/wireless/iwlwifi/mvm/coex_legacy.c
index 585c0ab..8a1d2f3 100644
--- a/drivers/net/wireless/iwlwifi/mvm/coex_legacy.c
+++ b/drivers/net/wireless/iwlwifi/mvm/coex_legacy.c
@@ -291,8 +291,8 @@ static const __le64 iwl_ci_mask[][3] = {
};

static const __le32 iwl_bt_mprio_lut[BT_COEX_MULTI_PRIO_LUT_SIZE] = {
- cpu_to_le32(0x28412201),
- cpu_to_le32(0x11118451),
+ cpu_to_le32(0x2e402280),
+ cpu_to_le32(0x7711a751),
};

struct corunning_block_luts {

[Emmanuel Grumbach]

From: Emmanuel Grumbach <emmanuel.grumbach-***@public.gmane.org>

The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.

Cc: <stable-***@public.gmane.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach-***@public.gmane.org>
---
drivers/net/wireless/iwlwifi/iwl-trans.h | 2 ++
drivers/net/wireless/iwlwifi/mvm/fw-api-power.h | 35 ++++++++++++++++++++++++-
drivers/net/wireless/iwlwifi/mvm/fw-api.h | 1 +
drivers/net/wireless/iwlwifi/mvm/fw.c | 9 +++++++
drivers/net/wireless/iwlwifi/mvm/ops.c | 1 +
drivers/net/wireless/iwlwifi/pcie/trans.c | 16 ++++++-----
6 files changed, 56 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/iwl-trans.h b/drivers/net/wireless/iwlwifi/iwl-trans.h
index 9eb8524..d8fc548 100644
--- a/drivers/net/wireless/iwlwifi/iwl-trans.h
+++ b/drivers/net/wireless/iwlwifi/iwl-trans.h
@@ -563,6 +563,7 @@ enum iwl_trans_state {
* Set during transport allocation.
* @hw_id_str: a string with info about HW ID. Set during transport allocation.
* @pm_support: set to true in start_hw if link pm is supported
+ * @ltr_enabled: set to true if the LTR is enabled
* @dev_cmd_pool: pool for Tx cmd allocation - for internal use only.
* The user should use iwl_trans_{alloc,free}_tx_cmd.
* @dev_cmd_headroom: room needed for the transport's private use before the
@@ -589,6 +590,7 @@ struct iwl_trans {
u8 rx_mpdu_cmd, rx_mpdu_cmd_hdr_size;

bool pm_support;
+ bool ltr_enabled;

/* The following fields are internal only */
struct kmem_cache *dev_cmd_pool;
diff --git a/drivers/net/wireless/iwlwifi/mvm/fw-api-power.h b/drivers/net/wireless/iwlwifi/mvm/fw-api-power.h
index 27dd863..2fd8ad4 100644
--- a/drivers/net/wireless/iwlwifi/mvm/fw-api-power.h
+++ b/drivers/net/wireless/iwlwifi/mvm/fw-api-power.h
@@ -68,13 +68,46 @@

/* Power Management Commands, Responses, Notifications */

+/**
+ * enum iwl_ltr_config_flags - masks for LTR config command flags
+ * @LTR_CFG_FLAG_FEATURE_ENABLE: Feature operational status
+ * @LTR_CFG_FLAG_HW_DIS_ON_SHADOW_REG_ACCESS: allow LTR change on shadow
+ * memory access
+ * @LTR_CFG_FLAG_HW_EN_SHRT_WR_THROUGH: allow LTR msg send on ANY LTR
+ * reg change
+ * @LTR_CFG_FLAG_HW_DIS_ON_D0_2_D3: allow LTR msg send on transition from
+ * D0 to D3
+ * @LTR_CFG_FLAG_SW_SET_SHORT: fixed static short LTR register
+ * @LTR_CFG_FLAG_SW_SET_LONG: fixed static short LONG register
+ * @LTR_CFG_FLAG_DENIE_C10_ON_PD: allow going into C10 on PD
+ */
+enum iwl_ltr_config_flags {
+ LTR_CFG_FLAG_FEATURE_ENABLE = BIT(0),
+ LTR_CFG_FLAG_HW_DIS_ON_SHADOW_REG_ACCESS = BIT(1),
+ LTR_CFG_FLAG_HW_EN_SHRT_WR_THROUGH = BIT(2),
+ LTR_CFG_FLAG_HW_DIS_ON_D0_2_D3 = BIT(3),
+ LTR_CFG_FLAG_SW_SET_SHORT = BIT(4),
+ LTR_CFG_FLAG_SW_SET_LONG = BIT(5),
+ LTR_CFG_FLAG_DENIE_C10_ON_PD = BIT(6),
+};
+
+/**
+ * struct iwl_ltr_config_cmd - configures the LTR
+ * @flags: See %enum iwl_ltr_config_flags
+ */
+struct iwl_ltr_config_cmd {
+ __le32 flags;
+ __le32 static_long;
+ __le32 static_short;
+} __packed;
+
/* Radio LP RX Energy Threshold measured in dBm */
#define POWER_LPRX_RSSI_THRESHOLD 75
#define POWER_LPRX_RSSI_THRESHOLD_MAX 94
#define POWER_LPRX_RSSI_THRESHOLD_MIN 30

/**
- * enum iwl_scan_flags - masks for power table command flags
+ * enum iwl_power_flags - masks for power table command flags
* @POWER_FLAGS_POWER_SAVE_ENA_MSK: '1' Allow to save power by turning off
* receiver and transmitter. '0' - does not allow.
* @POWER_FLAGS_POWER_MANAGEMENT_ENA_MSK: '0' Driver disables power management,
diff --git a/drivers/net/wireless/iwlwifi/mvm/fw-api.h b/drivers/net/wireless/iwlwifi/mvm/fw-api.h
index 667a922..c62575d 100644
--- a/drivers/net/wireless/iwlwifi/mvm/fw-api.h
+++ b/drivers/net/wireless/iwlwifi/mvm/fw-api.h
@@ -157,6 +157,7 @@ enum {
/* Power - legacy power table command */
POWER_TABLE_CMD = 0x77,
PSM_UAPSD_AP_MISBEHAVING_NOTIFICATION = 0x78,
+ LTR_CONFIG = 0xee,

/* Thermal Throttling*/
REPLY_THERMAL_MNG_BACKOFF = 0x7e,
diff --git a/drivers/net/wireless/iwlwifi/mvm/fw.c b/drivers/net/wireless/iwlwifi/mvm/fw.c
index 23fd711..e0d9f19 100644
--- a/drivers/net/wireless/iwlwifi/mvm/fw.c
+++ b/drivers/net/wireless/iwlwifi/mvm/fw.c
@@ -480,6 +480,15 @@ int iwl_mvm_up(struct iwl_mvm *mvm)
/* Initialize tx backoffs to the minimal possible */
iwl_mvm_tt_tx_backoff(mvm, 0);

+ if (mvm->trans->ltr_enabled) {
+ struct iwl_ltr_config_cmd cmd = {
+ .flags = cpu_to_le32(LTR_CFG_FLAG_FEATURE_ENABLE),
+ };
+
+ WARN_ON(iwl_mvm_send_cmd_pdu(mvm, LTR_CONFIG, 0,
+ sizeof(cmd), &cmd));
+ }
+
ret = iwl_mvm_power_update_device(mvm);
if (ret)
goto error;
diff --git a/drivers/net/wireless/iwlwifi/mvm/ops.c b/drivers/net/wireless/iwlwifi/mvm/ops.c
index 15aa298..48cb25a 100644
--- a/drivers/net/wireless/iwlwifi/mvm/ops.c
+++ b/drivers/net/wireless/iwlwifi/mvm/ops.c
@@ -336,6 +336,7 @@ static const char *const iwl_mvm_cmd_strings[REPLY_MAX] = {
CMD(DTS_MEASUREMENT_NOTIFICATION),
CMD(REPLY_THERMAL_MNG_BACKOFF),
CMD(MAC_PM_POWER_TABLE),
+ CMD(LTR_CONFIG),
CMD(BT_COEX_CI),
CMD(BT_COEX_UPDATE_SW_BOOST),
CMD(BT_COEX_UPDATE_CORUN_LUT),
diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c
index 1393bac..c706dba 100644
--- a/drivers/net/wireless/iwlwifi/pcie/trans.c
+++ b/drivers/net/wireless/iwlwifi/pcie/trans.c
@@ -174,6 +174,7 @@ static void iwl_pcie_apm_config(struct iwl_trans *trans)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
u16 lctl;
+ u16 cap;

/*
* HW bug W/A for instability in PCIe bus L0S->L1 transition.
@@ -184,16 +185,17 @@ static void iwl_pcie_apm_config(struct iwl_trans *trans)
* power savings, even without L1.
*/
pcie_capability_read_word(trans_pcie->pci_dev, PCI_EXP_LNKCTL, &lctl);
- if (lctl & PCI_EXP_LNKCTL_ASPM_L1) {
- /* L1-ASPM enabled; disable(!) L0S */
+ if (lctl & PCI_EXP_LNKCTL_ASPM_L1)
iwl_set_bit(trans, CSR_GIO_REG, CSR_GIO_REG_VAL_L0S_ENABLED);
- dev_info(trans->dev, "L1 Enabled; Disabling L0S\n");
- } else {
- /* L1-ASPM disabled; enable(!) L0S */
+ else
iwl_clear_bit(trans, CSR_GIO_REG, CSR_GIO_REG_VAL_L0S_ENABLED);
- dev_info(trans->dev, "L1 Disabled; Enabling L0S\n");
- }
trans->pm_support = !(lctl & PCI_EXP_LNKCTL_ASPM_L0S);
+
+ pcie_capability_read_word(trans_pcie->pci_dev, PCI_EXP_DEVCTL2, &cap);
+ trans->ltr_enabled = cap & PCI_EXP_DEVCTL2_LTR_EN;
+ dev_info(trans->dev, "L1 %sabled - LTR %sabled\n",
+ (lctl & PCI_EXP_LNKCTL_ASPM_L1) ? "En" : "Dis",
+ trans->ltr_enabled ? "En" : "Dis");
}

/*

[Emmanuel Grumbach]

From: Emmanuel Grumbach <emmanuel.grumbach-***@public.gmane.org>

When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:

iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]

Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.

This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581

But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:

https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809

Cc: <stable-***@public.gmane.org>
Depends-on: 77be2c54c5bd ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach-***@public.gmane.org>
---
drivers/net/wireless/iwlwifi/dvm/mac80211.c | 24 +++++++++++++-----------
1 file changed, 13 insertions(+), 11 deletions(-)

diff --git a/drivers/net/wireless/iwlwifi/dvm/mac80211.c b/drivers/net/wireless/iwlwifi/dvm/mac80211.c
index 2364a3c..cae692f 100644
--- a/drivers/net/wireless/iwlwifi/dvm/mac80211.c
+++ b/drivers/net/wireless/iwlwifi/dvm/mac80211.c
@@ -1095,6 +1095,7 @@ static void iwlagn_mac_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
u32 queues, bool drop)
{
struct iwl_priv *priv = IWL_MAC80211_GET_DVM(hw);
+ u32 scd_queues;

mutex_lock(&priv->mutex);
IWL_DEBUG_MAC80211(priv, "enter\n");
@@ -1108,18 +1109,19 @@ static void iwlagn_mac_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
goto done;
}

- /*
- * mac80211 will not push any more frames for transmit
- * until the flush is completed
- */
- if (drop) {
- IWL_DEBUG_MAC80211(priv, "send flush command\n");
- if (iwlagn_txfifo_flush(priv, 0)) {
- IWL_ERR(priv, "flush request fail\n");
- goto done;
- }
+ scd_queues = BIT(priv->cfg->base_params->num_of_queues) - 1;
+ scd_queues &= ~(BIT(IWL_IPAN_CMD_QUEUE_NUM) |
+ BIT(IWL_DEFAULT_CMD_QUEUE_NUM));
+
+ if (vif)
+ scd_queues &= ~BIT(vif->hw_queue[IEEE80211_AC_VO]);
+
+ IWL_DEBUG_TX_QUEUES(priv, "Flushing SCD queues: 0x%x\n", scd_queues);
+ if (iwlagn_txfifo_flush(priv, scd_queues)) {
+ IWL_ERR(priv, "flush request fail\n");
+ goto done;
}
- IWL_DEBUG_MAC80211(priv, "wait transmit/flush all frames\n");
+ IWL_DEBUG_TX_QUEUES(priv, "wait transmit/flush all frames\n");
iwl_trans_wait_tx_queue_empty(priv->trans, 0xffffffff);
done:
mutex_unlock(&priv->mutex);